Skip to content
VULTAE

Certification & Compliance

EV Charger Operating Temperature Range: How to Read the Rating

What the operating temperature range on an EV charger data sheet means, how it differs from derating and storage limits, and what to ask for hot sites.

Prepared by
VULTAE Engineering Team
Published
Reading time
2 min
Sources
1 references

Key takeaways

  1. 1The operating temperature range is the ambient air temperature in which the charger is rated to work. It is not the same as the storage range, the temperature inside the cabinet or the point where output power starts to drop.
  2. 2Check three things on a data sheet: the ambient range, whether the rating is for full power or for reduced power, and the conditions such as direct sun or altitude. If any of them is missing, ask for it in writing.
  3. 3For hot sites, ask for the rating of the exact model you are buying, plan shade and airflow and verify with a loaded sample test.
An outdoor wall-mounted EV charger in strong sun with a car charging beside it
An outdoor wall-mounted EV charger in strong sun with a car charging beside it
Contents
  1. 01Four temperatures that get mixed up
  2. 02What to check on the data sheet
  3. 03Hot and cold sites
  4. 04How to verify the figure
  5. 05For a purchase order

Short answer: the operating temperature range is the ambient air in which the charger is rated to work. Read it together with derating behaviour, sun exposure and the model it applies to.

Four temperatures that get mixed up

Temperature What it means Where you find it
Operating (ambient) range Air temperature around the charger in use Data sheet, nameplate or manual
Storage range Temperature when switched off, in storage or transport Data sheet
Internal component temperature Temperature inside the cabinet, higher than ambient Charger logs
Derating threshold Point where output starts to fall to protect parts Manual or data sheet note

Two chargers can show the same ambient range but behave differently at the top end: one holds full power, the other drops to half.

What to check on the data sheet

  1. The range itself, for example from a low limit to a high limit in degrees Celsius.
  2. Full power or reduced power: does the charger deliver its rated output across the whole range?
  3. Conditions: direct sun, altitude, humidity and installation position.
  4. Model scope: the rating applies to which model and version? Ratings can differ between series and between the IEC and North American versions.
  5. Test evidence: a test report or type test that supports the figure; see what a factory test report should show.

Hot and cold sites

Site Main concern What helps
Desert, Gulf, tropical Heat, sun load, dust Shade, canopy, airflow, filters; see hot climates
Cold regions Cable stiffness, condensation, screens Rated low limit, heater options; see cold climates
Enclosed garages Poor ventilation Spacing, ventilation, load management

For outdoor sites also check the ingress rating; see IP and IK ratings.

How to verify the figure

  • Ask in writing for the ambient range and the derating curve of the exact model.
  • Run a loaded sample test at your expected temperature or in a heat chamber; see what to test before a bulk order.
  • Log temperature during the pilot installation and compare with the data sheet.
  • Plan the site: shade over the charger, clearance around vents and no heat sources next to it.

For a purchase order

Write the operating range and the requirement for rated output at the top of that range into the specification, and make acceptance depend on a test. See how to write a tender specification.

VULTAE can supply the data sheet for your exact model, including its rated operating temperature, and discuss site conditions before you order.

Questions buyers ask

What is the difference between operating and storage temperature?
Operating temperature is the ambient range in which the charger is designed to work. Storage temperature is the range it can survive when switched off, for example in a warehouse or container. The storage range is usually wider.
What is derating?
A controlled reduction of output power when internal temperatures rise, to protect the components. It is normal behaviour and should be described in the data sheet. See the article on hot climates for details.
Does direct sun matter?
Yes. A charger in direct sun runs warmer than the air temperature. Shade and ventilation keep internal temperatures lower and help the charger hold full power for longer.

References

  1. [1]IEC 61851-1 Electric vehicle conductive charging system. International Electrotechnical Commission.

Equipment

Chargers referred to in this guide

Tell us what you’re building

Send your market, charger type, power and quantity — our engineers reply with matching models, specifications and pricing.

WhatsAppRequest a quote